Pt-Sn/Al2O3蜂窝催化剂催化氧化C6烃

采用等体积分浸法制备Pt-Sn/Al₂O₃蜂窝催化剂（Pt含量仅为0.06wt%）.运用X射线衍射（XRD）、透射电镜（TEM）等技术对催化剂理化性质进行表征,并选取4种代表性C₆烃（苯、环己酮、环己烷和正己烷）对催化剂性能进行评价.活性评价试验中,Pt/Sn比为3/1催化效果最佳.此时4种C₆烃转化率达到90%的温度（T₉₀）较Pt催化剂均降低约20℃,其原因在于Sn可将Pt分割为较小的团簇提高Pt分散度.寿命评价试验以环己烷为例同Pt-Sn蜂窝催化剂连续运行720h,催化活性无明显变化,其原因在于,Sn可有效抑制其粒径增长;Pt₃Sn合金降低表面对C₆烃的吸附,减少催化剂表面积炭.     

基于全过程治理的环境规制减排机制研究——来自长江经济带数据的实证检验

基于2007~2017年长江经济带11个省市的面板数据,利用中介效应模型探究全过程治理视域下政府主导型和市场激励型2类环境规制的减排机制.研究发现,政府主导型环境规制和市场激励型环境规制对SO₂排放均具有显著的抑制作用,其影响系数分别为-0.154和-0.209.其中政府主导型环境规制在源头防控、过程控制和末端治理的全过程都起到显著的减排效应,而市场激励型环境规制只通过末端治理实现减排.因此,尽管市场激励型环境规制具有低成本、高效率的优点,但考虑到源头防控和过程控制在生态环境保护中发挥的根本性作用,对于经济结构和经济发展方式较为落后的地区和行业,仍要重视以政府为主导的环境规制,通过因地制宜、合理科学地运用环境规制工具以实现高效的全过程污染治理.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Dynamic nano-Ag colloids cytotoxicity to and accumulation by Escherichia coli: Effects of Fe3+, ionic strength and humic acid

Released Ag ions or/and Ag particles are believed to contribute to the cytotoxicity of Ag nanomaterials, and thus, the cytotoxicity and mechanism of Ag nanomaterials should be dynamic in water due to unfixed Ag particle:Ag⁺ ratios. Our recent research found that the cytotoxicity of PVP-Ag nanoparticles is attributable to Ag particles alone in 3 hr bioassays, and shifts to both Ag particles and released Ag⁺ in 48 hr bioassays. Herein, as a continued study, the cytotoxicity and accumulation of 50 and 100 nm Ag colloids in Escherichia coli were determined dynamically. The cytotoxicity and mechanisms of nano-Ag colloids are dynamic throughout exposure and are derived from both Ag ions and particles. Ag accumulation by E. coli is derived mainly from extracellular Ag particles during the initial 12 hr of exposure, and thereafter mainly from intracellular Ag ions. Fe³⁺ accelerates the oxidative dissolution of nano-Ag colloids, which results in decreasing amounts of Ag particles and particle-related toxicity. Na⁺ stabilizes nano-Ag colloids, thereby decreasing the bioavailability of Ag particles and particle-related toxicity. Humic acid (HA) binds Ag⁺ to form Ag⁺-HA, decreasing ion-related toxicity and binding to the E. coli surface, decreasing particle-related toxicity. HA in complex conditions showed a stronger relative contribution to toxicity and accumulation than Na⁺ or Fe³⁺. The results highlighted the cytotoxicity and mechanism of nano-Ag colloids are dynamic and affected by environmental factors, and therefore exposure duration and water chemistry should be seriously considered in environmental and health risk assessments.     

An investigation of changes in water quality throughout the drinking water production/distribution chain using toxicological and fluorescence analyses

Changes in water quality from source water to finished water and tap water at two conventional drinking water treatment plants(DWTPs) were monitored.Beside the routine water quality testing,Caenorhabditis elegans-based toxicity assays and the fluorescence excitation–emission matrices technique were also applied.Both DWTPs supplied drinking water that met government standards.Under current test conditions,both the investigated finished water and tap water samples exhibited stronger lethal,genotoxic and reprotoxic potential than the relative source water sample,and the tap water sample was more lethal but tended to be less genotoxic than the corresponding finished water sample.Meanwhile,the nearly complete removal of tryptophan-like substances and newly generated tyrosine-like substances were observed after the treatment of drinking water,and humic-like substances were identified in the tap water.Based on these findings,toxic pollutants,including genotoxic/reproductive toxicants,are produced in the drinking water treatment and/or distribution processes.Moreover,further studies are needed to clarify the potentially important roles of tyrosine-like and humic-like substances in mediating drinking water toxicity and to identify the potential sources of these contaminants.Additionally,tryptophan-like fluorescence may be adopted as a useful parameter to monitor the treatment performance of DWTPs.Our observations provided insights into the importance of utilizing biotoxicity assays and fluorescence spectroscopy as tools to complement the routine evaluation of drinking water.     

Synergistic effects of Cu species and acidity of Cu-ZSM-5 on catalytic performance for selective catalytic oxidation of n-butylamine

In this work, a series of Cu-ZSM-5 catalysts with different SiO₂/Al₂O₃ ratios (25, 50, 100 and 200) were synthesized and investigated in n-butylamine catalytic degradation. The n-butylamine can be completely catalytic degradation at 350°C over all Cu-ZSM-5 catalysts. Moreover, Cu-ZSM-5 (25) exhibited the highest selectivity to N₂, exceeding 90% at 350°C. These samples were investigated in detail by several characterizations to illuminate the dependence of the catalytic performance on redox properties, Cu species, and acidity. The characterization results proved that the redox properties and chemisorption oxygen primarily affect n-butylamine conversion. N₂ selectivity was impacted by the Brønsted acidity and the isolated Cu²⁺ species. Meanwhile, the surface acid sites over Cu-ZSM-5 catalysts could influence the formation of Cu species. Furthermore, in situ diffuse reflectance infrared Fourier transform spectra was adopted to explore the reaction mechanism. The Cu-ZSM-5 catalysts are the most prospective catalysts for nitrogen-containing volatile organic compounds removal, and the results in this study could provide new insights into catalysts design for VOC catalytic oxidation.     

Ozone pollution characteristics and sensitivity analysis using an observation-based model in Nanjing, Yangtze River Delta Region of China

Ground-level ozone (O₃) has become a critical pollutant impeding air quality improvement in Yangtze River Delta region of China. In this study, we present O₃ pollution characteristics based on one-year online measurements during 2016 at an urban site in Nanjing, Jiangsu Province. Then, the sensitivity of O₃ to its precursors during 2 O₃ pollution episodes in August was analyzed using a box model based on observation (OBM). The relative incremental reactivity (RIR) of hydrocarbons was larger than other precursors, suggesting that hydrocarbons played the dominant role in O₃ formation. The RIR values for NO_X ranged from –0.41%/% to 0.19%/%. The O₃ sensitivity was also analyzed based on relationship of simulated O₃ production rates with reductions of VOC and NO_X derived from scenario analyses. Simulation results illustrate that O₃ formation was between VOCs-limited and transition regime. Xylenes and light alkenes were found to be key species in O₃ formation according to RIR values, and their sources were determined using the Positive Matrix Factorization (PMF) model. Paints and solvent use was the largest contributor to xylenes (54%), while petrochemical industry was the most important source to propene (82%). Discussions on VOCs and NO_X reduction schemes suggest that the 5% O₃ control goal can be achieved by reducing VOCs by 20%. To obtain 10% O₃ control goal, VOCs need to be reduced by 30% with VOCs/NO_X larger than 3:1.     

餐厨垃圾生物有机肥对贫瘠黄褐土改良的研究

为了阐明餐厨垃圾生物有机肥改良贫瘠土壤的作用机制,以贫瘠黄褐土为研究对象,通过不施肥、长期（>5 a）施用化肥、中长期（5 a）施用少量餐厨垃圾生物有机肥和短期（1 a）施用大量餐厨垃圾生物有机肥4种施肥方式,分别记为CK组、CF组、LOF-5组和MOF-1组,对比分析不同施肥方式对土壤OM（有机质）、活性有机碳、营养元素和团聚体等的影响.结果表明:①施用餐厨垃圾生物有机肥可显著提高土壤OM、活性有机碳含量,其中,MOF-1组提高效果最显著,与CK组相比,w（OM）可提高173.29%,w（ROC）（ROC为易氧化有机碳）增加了39.17%,w（POC）（POC为颗粒有机碳）和w（DOC）（DOC为可溶性有机碳）分别是CK组的13.85和10.32倍.②中长期（5 a）施用少量餐厨垃圾生物有机肥可增加土壤中较大粒径团聚体的占比,且更有利于提高土壤团粒结构的稳定性,LOF-5组>2 mm粒级的团聚体占比是CK组的4.68倍;与CK组相比,LOF-5组MWD（平均重量直径）增加了100.00%,GMD（几何平均直径）增加了82.98%,>0.25 mm水稳定性团聚体质量占比（DR_0.25）增加了27.20%.③中长期（5 a）施用少量餐厨垃圾生物有机肥可增加土壤中w（TN）（TN为全氮）和w（AN）（AN为速效氮）,与CK组相比,LOF-5组w（TN）和w（AN）分别增加了77.42%和20.82%.施用餐厨垃圾有机肥也可同时增加土壤中w（AP）（AP为速效磷）和w（AK）（AK为速效钾）,MOF-1组增加效果较佳,w（AP）和w（AK）分别是CK组的9.43和3.39倍.研究显示,中长期（5 a）施用少量餐厨垃圾生物有机肥可提升土壤固碳能力,提高土壤养分利用的有效性,从而提升耕地土壤质量,减少化肥施用量,是我国贫瘠黄褐土改良的有效施肥模式.      

水稻秸秆生物炭中铜和镉的形态分布及释放特性

由于目前缺乏对生物质原料来源的管控办法,极有可能用产自受污染农田土壤的秸秆制备出具有高重金属含量的生物炭,因此,研究生物炭中重金属的形态分布及其释放特性对于防控生物炭应用产生的环境风险具有重要意义.基于此,分别采集江西省贵溪铜冶炼厂周边九牛岗污染区和中国科学院鹰潭红壤生态实验站清洁区种植的水稻秸秆制备生物炭（分别记为“九牛岗生物炭”和“红壤站生物炭”）,分析两种生物炭中Cu、Cd的含量及其化学形态分布,考察不同固液比及pH对生物炭中Cu、Cd浸出的影响.结果表明:九牛岗生物炭中Cu、Cd的总量（以w计）分别为119.99、3.83 mg/kg,显著高于红壤站生物炭（19.50、0.96 mg/kg）.尽管九牛岗生物炭中w（酸溶态Cu）、w（酸溶态Cd）显著高于红壤站生物炭,但在形态分布上,九牛岗生物炭中Cu、Cd主要为相对稳定态（可氧化态和残渣态）,二者占比分别为80.3%、76.7%,高于红壤站生物炭（二者占比分别为53.2%、48.0%）.高固液比和低pH可有效增加两种生物炭中Cu、Cd的浸出毒性,其中,九牛岗生物炭在固液比为1:20和1:60时,浸出液中ρ（Cu）、ρ（Cd）均超过GB/T 14848—2017《地下水质量标准》中Ⅱ类标准限值.动力学及累积释放试验表明,两种生物炭中的部分Cu、Cd可在短时间内迅速释放而后逐渐平稳并有上升趋势,且九牛岗生物炭中Cu、Cd释放量显著高于红壤站生物炭.研究显示,来自污染区水稻秸秆生物炭中的Cu、Cd活性显著高于清洁区生物炭,具有更高的环境风险.      

碳氮比对蔬菜废弃物好氧发酵腐熟度及臭气排放的影响

为了提高蔬菜废弃物发酵效率、减少臭气排放、确定其好氧发酵最佳碳氮比,以蔬菜废弃物为主料、猪粪和玉米秸秆为辅料进行好氧发酵,设置C/N为20、25、30 3个处理,探讨不同C/N对发酵产品腐熟度及臭气排放浓度的影响,以温度、含水率、pH、电导率(EC)、腐植酸光学特性(E₄/E₆值)、种子发芽指数以及全氮、全磷、全钾含量变化评价发酵产品的腐熟度。T1处理(C/N为20)高温期持续时间最长为6 d,种子发芽指数最高为82.23%,其腐熟效果最好,且全氮、全磷、全钾含量分别提高了24.22%、78.94%、51.45%; 从臭气排放浓度来看,T2 (C/N为25)处理组NH₃排放浓度最高达368000 μg/m3,T3(C/N=30)处理组H₂S排放浓度最高达671 μg/m3,TI处理TVOC排放浓度最高,但最高与最低排放浓度差仅为4.3×10-6。因此,建议蔬菜废弃物、猪粪、玉米秸秆联合好氧堆肥的C/N为20,可满足好氧发酵无害化和减少臭气排放的要求。